755-Series ability to 'use' the ultrabay CD-ROM from the 755CD and CDV

solidpro

Rather New Member
Themenstarter
Registriert
29 Mai 2022
Beiträge
16
Sorry for posting in English but there are some good opinions in here!

I'd recently posted for sale a rare 755CDV but with an odd problem whereby when you connect it's CD-ROM drive, it won't power on. Obviously one key feature of the 755CDV besides it's detachable display is the fact it's the joint-first laptop ever with a built-in CD-ROM drive (the 755CD being the first). So I set about trying to work out why, or at least a pattern.

tried the drive in another 755CD and it did the same - no POST. So I first thought 'its the drive' that's the problem, not the machine.
So I took out the (working) CD-ROM drive in the 755CD and put that in the 755CDV and it also had the same symptoms as before - would not POST.

So at this point, I try not to make the mistake many do whereby they do not adapt their thoughts away from 'single problem' mentality. I feel I've probably got two problems. The issue follows the 1st CD-ROM drive, so it's that and that the 755CDV also will not accept any known good CD-ROM drive.

I tried an ultrabay floppy in both machines and they both work fine.
I tried removing the HDD (which would likely be on the same IDE bus) and it didn't make any difference.
I checked the Systemboard type and BIOS - I've upgraded all my 755 machines up to the latest BIOS and the problem is exactly the same on all System boards (P75 and DX4-100), all running latest BIOS.

There are two subtle differences when a machine won't POST. Sometimes I get a long, solid beep - which is an unusual fault alert with a Thinkpad 755, not one I've come across before. And the second 'not-posting' issue is just nothing comes on the screen. No sound, the machine is powered up and even will spin up the HDD and blink the LEDs normally, but nothing ever appears.

Before I downed tools for the day, I built on a bench a 486 DX-4-100 with an identical hardware setup to the 755CDV using a spare system board I had and spare 755CD daughterboards and it accepts *all* the CD-ROM drives!!

So I think I have a CD-ROM drive which is picky as to what it will run on, and some system boards which simply will not accept a CD-ROM drive in the ultrabay.

I still have some further troubleshooting to do but I wondered has anyone else had any memories or experiences with issues using an ultrabay CD-ROM drive on the 755-enhanced models?

My final thought is that despite all 755-enhanced system boards having the same part number and being interchangable, perhaps they are not if your chassis is expecting CD-ROM compatibility. (IBM offered an upgrade of the same system board from 486 to Pentium by swapping out the memory and the CPU complex) . If the 755CD and CDV from the factory are the only 755 machines which will accept an ultrabay CD-ROM drive, it would be extremely odd and curious but seeing as they were bleeding edge, theoretically plausible.

All the best
 
What´s about the battery : still installed and working fine ?
Even recent TPs have "funny" reaction to dead or dying batteries .
My advice is to run your 755 with power from the wallsocket alone ,battery removed ...

Greets Uwe

P.S.: You´ve got a real nice website !
 
Yeah I take the main batteries out of all my machines, at least when I'm testing them because they can cause odd behaviour. Thanks!
 
I've almost solved it with a few things to tie up. The issue with the machine not being able to power up with the CD-ROM was being impeded with it sometimes powering on and then powering off again. This was actually happening with more system boards than not and turned out to be not system-board related and was actually being caused by a seperate chain of events. The keyboard open latch was kicking off a suspend, but this would only happen when the machine was fully booted into W95 or MS-DOS - which explained why the machine functioned perfectly well in Easy Setup or MS-DOS setup.

So I'm just going to lay down all the gotchas which are not obvious in the HMM or troubleshooting guides.

  1. If you're troubleshooting an incomplete chassis, tape down the keyboard-lift latch. Otherwise it may be causing shut downs which aren't immediately obvious why - especially if you don't have the LED indicator bezel attached showing the "Suspend" LED lit. Also not having a speaker attached removes the tell-tale 'beep beep' from a Thinkpad saying I'm in suspend and there is a reason I won't come out.
  2. The 755 machines had factory options between 486-DX4-100 and Pentium 75, which was on a detachable CPU card. It does not mention anywhere that the RAM is associated with the type of CPU and you must have the eqivilent 486 or Pentium-associated RAM. They do have different part codes, but often only thr 486 part code is mentioned.
  3. The detachable internal 486 RAM does appear to sometimes go bad and cause a 201 much like if you have the wrong RAM connected. This will usually also cause it only showing 4Mb instead of 8 which is impossible to my knowledge because the only 755s with 4Mb RAM did not have detachable internal RAM.
  4. Initially all the DC cards appear to be interchangable by simply removing the single speaker if you have a dual speaker CD/CDV machine. However if you look closely, besides the seperate part code, there are lots of different passive components which may affect the power capacity to run all the extras a CD/CDV have over the FDD/non-multimedia models.
  5. Many system boards have 85G1493 which I can't find referenced on any IBM doc. Perhaps they would have all been re-labelled later to relate to the exact machine they went in, but I can only see these are 'related' to the 85G1141 which is the CD/CDV board.
  6. Sometimes, rarely - but sometimes the 755-series machines get 'stuck' after the RAM test and do not do anything. No errors, no booting, no F1 for Easy Setup. You can reset the CMOS and start again but you'll get into set clock and then often back at the same 'stuck' bit where it looks like it's waiting for something. The only way I've found to get over this is connect a FDD and let it boot to something. Often this will resolve the 'stuckness' of the 755.
 
Zuletzt bearbeitet:
  • ok1.de
  • thinkstore24.de
  • ok2.de - Notebook Computer Server
  • Preiswerte-IT - Gebrauchte Lenovo Notebooks kaufen

Werbung

Zurück
Oben